BT-PON ONU BT-7xxXR/BT-3xxXR Web Configuration Guide

This guidance document is applicable to BT-7xxXR/BT-3xxXR series models ONU equipment of BT-PON.

YouTube video
You can also refer to our tutorial video to set it up.

1.Web Login

Login URL:http://192.168.1.1
user login account:useradmin ; password:123456
After entering the username and password correctly, click Login button to enter the web management interface.

2.ONU Status

login successfully enter the Web page look over Device Status
Device Status:

PON Status:
View TX, RX information:

WAN connections Status:

WLAN Configuration:

CATV Status:

3.WAN Connection Create

To set up the WAN Connection, you need to log into the ONU administration page with a super administration account. Create multiple WAN connections (PPPOE, TR069 (DHCP), VOIP (DHCP), IPTV):

3.1 Create PPPOE WAN connection configuration

Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(PPPoE internet VLAN ID)
Channel Mode: PPPoE
Connection Type: INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
UserName: PPPoE AUthorized Username.
Password: PPPoE Authorized Password.
Select the corresponding port map
LAN_1 LAN_2
LAN_3 LAN_4
WLAN0( WLAN0 is 5.8g wifi )
WLAN1( WLAN1 is 2.4g wifi )
Click the Apply Changes button (Save the configuration)

3.2 Create DHCP WAN connection configuration

Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select

VLAN ID: select (PPPoE internet VLAN ID)
Channel Mode: IPoE
Connection Type: INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
Select the corresponding port map
LAN_1 LAN_2
LAN_3 LAN_4
WLAN0( WLAN0 is 5.8g wifi)
WLAN1( WLAN1 is 2.4g wifi)
Click the Apply Changes button (Save the configuration)

3.3 Create TR069 WAN connection and TR069 configuration

Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(PPPoE internet VLAN ID)
Channel Mode: IPoE
Connection Type: TR069 or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
No need to ping ports
Click the Apply Changes button (Save the configuration)
Enter the Admin
TR-069: Select
URL: http://192.168.88.250:80/acs
Click the Apply button (Save the configuration)

3.4 Create VoIP WAN and VoIP configuration

Create a VoIP WAN connection :
Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(IPoE internet VLAN ID)
Channel Mode: IPoE
Connection Type: VOICE selects INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
Select the corresponding port map
LAN_1 LAN_2
LAN_3 LAN_4
WLAN0( WLAN0 is 5 g internet)
WLAN1( WLAN1 is 2.4 g internet)
Enter: Apply Changes (Save the configuration)

Enter the VOIP
Viop line 1: select
Display Name:
Number:
Login ID:
Password:
Proxy: select enable
Proxy Addr: Proxy server address
Apply: select

3.5 Create IPTV WAN Connection and IPTV configuration

Create a IPTV WAN connection:
Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select(IPoE internet VLAN ID)
Channel Mode: Bridged
Connection Type: Other selects INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
LAN PORT Binding: select LAN2(IPTV PORT)
Enter: Apply Changes (Save the configuration)
Enter the Admin
Multicast Vlan: select
Select the newly created IPTV WAN connection.Select modify under the corresponding WAN connection.Select modified prompt to set multicast VLAN
Setup Multicast Vlan:IPTV VLAN ID
Apply: select

3.6 Create IPTV WAN Connection and IPTV configuration

Create a IPTV WAN connection:
Enter the WAN—->PON WAN, configure the relevant information, and click the APPLY button.
Connection Name: select new link
Enable VLAN: select
VLAN ID: select( internet VLAN ID)
Channel Mode: IPoE
Connection Type: INTERNET selects INTERNET or TR069_INTERNET or TR069_VOICE_INTERNET or VOICE_INTERNET
IP Protocol: IPV4
Type: DHCP
LAN PORT Binding: select LAN2(IPTV PORT)
Enter: Apply Changes (Save the configuration)
Enter the Admin
Multicast Vlan: select
Select the newly created IPTV WAN connection. Select modify under the corresponding WAN connection. Select modified prompt to set multicast VLAN
Setup Multicast Vlan: IPTV VLAN ID
Apply: select

4.LAN interface configuration

4.1 LAN IP Setting

Enter the LAN: LAN interface modification LAN_IP address configuration:
LAN:Select(LAN interface settings)
IP Address: 192.168.xxx.xxx
Subnet Mask: 255.255.255.0
IP Version: IPV4/IPV6
Click the APPLY button
The reboot will not take effect until the IP is set

4.2 Modify LAN IP Address Pool

Modify LAN IP address pool configuration:
Enter the LAN: LAN interface modification
LAN: Select(LAN interface settings)
IPV4: Select
IP Pool Range: 192.168.xxx.2——192.168.xxx.254(Start Addres – End Address)
Subnet Mask: 255.255.255.0
Gateway Address: 192.168.xxx.xxx
Click the Apply Changes button

5. 5g WIFI Configuration

5.1 5g WIFI SSID Configuration Modify WIFI SSIDConfiguration:

Enter the WLAN
Basic Settings: Select
SSID: Modifiable.
Click the Apply Changes button
Close the 5g wireless

Modify wireless mode adn Channel Width,CHannel Number.

To modify the wireless channel, the default is auto. If you can’t find a wireless signal on your phone, change the value of the wireless channel to 149 and try again.

To modify the 5g wireless SSID and password
Enter the WLAN
Security: Select
Pre-Shared Key: Modifiable.
Click the Apply Changes button

6. 2.4g WIFI Configuration

6.1 2.4g WIFI SSID, wireless mode adn Channel Width,Channel Number.Configuration

Enter the WLAN
WLAN1(2.4GHz)
Basic Settings: Select
SSID.wireless mode. Channel Width. CHannel Number :Modifiable.
Click the Apply Changes button
To modify the wireless channel, the default is auto. If you can’t find a wireless signal on your phone, change the value of the wireless channel to 1 and try again

Close the 2.4g wireless

To modify the 2.4g wireless SSID and password
Enter the WLAN
WLAN1(2.4GHz)
Security: Select
Pre-Shared Key: Modifiable.
Click the Apply Changes button

7.Turn on and off the CATV interface functions

Enter the Admin
CATV Confinguration: select
Enable CATV: Select
Click the Apply button

8. Enable remote access ONU to manage web pages.(that is, open access to the HTTP port of the wan interface)

Enter the Admin
ACL: select
Interface: WAN
HTTP: select
Click the Update button

9. SoftWare Upgrade

WEB page upgrade guide
WEB page upgrade configuration:
Enter the Admin
Firmware Upgrade: select
Click Select the file button: Select the file you want to upgrade
Click Upgraed button
click the “Select the file” button, select the suffix name. bin upgrade file, and then click the Upgrade button. Wait 3-4 minutes, the device will restart automatically after the upgrade is completed.